Quantum-composers 9250 Series Manuel d'utilisateur Page 26
- Page / 51
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
9250 Manual Version 1.2 | Quantum Composers
26
Single Shot Mode
Pressing the unit’s Run/Stop button generates a single pulse with every press. Set the
following parameters in the 9250 application:
Within the System section:
o Select Single Shot mode.
Within the Channel section:
o Set channel mode to Normal.
o Enter the required pulse width and delay. Repeat for each output channel.
o Enable the corresponding channels by clicking “Enabled” in the 9250 application.
Pressing the unit’s Run/Stop button will now generate one pulse out of every enabled channel.
System Burst Mode Function
The Run/Stop button generates a stream of ‘N’ T
0
pulses, where the ‘N’ is specified by the
Burst parameter. The rate is specified by the Period parameter. Pressing the Run/Stop button
while the burst is in process will stop the output. After the burst has been completed, Pressing
the Run/Stop button will generate another burst of pulses. To generate a burst of pulses set
the following parameters in the 9250 application:
Within the System section:
o Select mode to be Burst.
o Set the Burst Count parameter field to produce the number of pulses desired
o Set the desired Period.
Within the Channel section:
o Set channel mode to Normal.
o Enter the required pulse width and delay. Repeat for each output channel.
o Enable the corresponding channels by clicking “Enabled” in the 9250 application.
Pressing the unit’s Run/Stop button will now generate the predefined burst of pulses out of
every enabled channel.
System Duty Cycle Function
The Run/Stop button starts a continuous stream of T
0
pulses, which repeats for ‘N’ pulses On
and ‘M’ pulses Off, where ‘N’ and ‘M’ are specified by the On/Off parameters respectively. The
rate at which the pulses are generated is controlled by the Period parameter. To generate a
stream of pulses which will repeat for ‘N’ pulses On and ‘M’ pulses, set the following
parameters in the 9250 application:
Within the System section:
o Set the mode to Duty Cycle.
o Set the On parameter to number of pulses to produce during the on cycle (‘N’).
o Set the Off parameter to number of pulses to suppress during the off cycle (‘M’).
o Set the desired Period.
- Contents 2
- 1. Introduction 5
- 2. Safety Issues 6
- Front Panel 7
- Back Panel 8
- System Timer Functions 9
- Channel Timer Functions 10
- Digital Output Multiplexer 10
- Navigating the 9250 11
- Enabling System Output 11
- Smooth Transition Updating 11
- 5. 9250 Setup 13
- 6. 9250 Application 15
- Basic Operation 16
- Channels Section 18
- Virtual Channels 20
- Enhanced Options 21
- Command Terminal 22
- Parameter Storage 22
- 9250 Application Example 23
- 7. Operating the 9250 25
- Single Shot Mode 26
- System Burst Mode Function 26
- System Duty Cycle Function 26
- Channel Timer Overview 27
- Channel Burst Mode 28
- Channel Duty Cycle Mode 28
- External Input Overview 29
- Output Examples 31
- 8. Programming the 9250 32
- Line Termination 33
- SCPI Command Keywords 33
- SCPI Command Format 34
- SCPI Keyword Separator 34
- SCPI Optional Keywords 34
- SCPI Parameter Types 35
- Error Codes 35
- Programming Examples 35
- 9250 SCPI Command Summary 37
- *Note: commas should be 40
- IEEE 488.2 Common Commands 41
- 9250 Specifications 42
- Channel Timing Generator 43
- Trigger/Gate Input Module 43
- Output Module 44
- Communications 44
- General 44
- Overview 45
- TZ50 Specifications 47
- Terminating Into 50 Ohms 48
- Safety Marking Symbols 49
Produits connexes et manuels pour Générateurs Quantum-composers 9250 Series
(3 pages)SurgeX SA-966 manuály
Uživatelské manuály a uživatelské příručky pro Přepěťové ochrany SurgeX SA-966.
Poskytujeme 1 manuály pdf SurgeX SA-966 ke stažení zdarma podle typů dokumentů: Instalační manuál
Commentaires sur ces manuels