Quantum-composers AF910 Manuel d'utilisateur Page 31
- Page / 39
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
AF910 Manual Version 1.4 Page 31
SO ####, SO? Sensor Offset. This is an objective specific offset that should be
set before data is collected off the sensor array. Each value is a
multiple of 8. The default is 2, which means that 2 x 8 = 16 pixels
of the linear array will be ignored before data is captured. This
command will allow the system to ignore a section of the array
data when determining the focus position. Values are from 0x0000
to 0x0020. A “?” will return the current offset value.
SP?, SP L?,
SP L ####
SP H?, SP H ####
Speed. Sets the motor clock speed output. A “?” will return the
active speed. The last speed changed is by default the active speed
and the motor will move at that speed if no other commands are
altered before the move command is sent. Step rates are 16 bit hex
values based on the following decimal calculations:
Rate = 20,000,000/(65,536-Value)
Value = 65,536 – (20,000,000/Rate)
The maximum step rate available is ~80KHz or a decimal value of
65300. Rates above 10KHz may have an error of ~10%. A “H”
parameter sets the high speed value that is used when the focus is
outside of the docking area. A “L” parameter sets the low speed
which is used once focus is inside the docking range.
SP M Speed Maximum. This command returns the current max speed
for the system. Values will range from 0x0000 to 0xFFFF.
SS System Status. Returns two bytes that indicate the status of
various system states.
7
6
5
4
3
2
1
0
Signal
Power Too
High
Signal
Power Too
Low
High
Sensor
Gain
Invalid
Data
Auto
Focus
Enabled
In
Docking
Range
In Focus
Range
In Focus
15
14
13
12
11
10
9
8
Area
Invalid
Power
Invalid
CoM
Invalid
Peak
Invalid
Intensity
Error
EMO
Status
Laser
Disabled
Auto
Motor
ST Stop. Stops motor movement. This will stop the motor and take it
out of auto motor mode if enabled.
VN Version Number. Returns the firmware revision number as a 3-
digit number followed by a release Alpha character in the format
“m.nnr”, where m = major version, n = minor version and r is the
release build. Ex: 1.22A.
- AF910 – Autofocus 1
- Operating Manual 1
- Table of Contents 2
- PREFACE 3
- CHAPTER 1 – Product Overview 4
- Accessories 5
- CHAPTER 2 - Safety 6
- Laser Safety 7
- Safety Labels and Locations 9
- Figure 2 Laser Radiation 10
- Figure 3 Laser Aperture 10
- CHAPTER 3 – Installation 11
- Methods of Operation 13
- Software Quick Start 13
- Figure 6 Autofocus Enable 14
- Figure 9 Focus Windows 15
- Figure 12 Autofocus Data 16
- Analog and Digital I/O 17
- Figure 14 Analog Output 18
- Figure 19 Motor Home Speed 21
- Figure 20 Limit Switch Setup 21
- Figure 21 Home Function 21
- Figure 22 Reverse Homing 21
- Figure 23 Step Counter 22
- Figure 24 Motor Movements 22
- Figure 25 Motor Drive Mode 22
- Figure 26 23
- Figure 27 24
- Communicating with the AF910 25
- Command Set 26
- CHAPTER 7 – Maintenance 32
- Problem 33
- Solution 33
- CHAPTER 10 – Appendixes 34
- Mechanical Dimensions 35
- Main Sensor Connection 35
- Warranty 39
- Feedback 39
Produits connexes et manuels pour Générateurs Quantum-composers AF910
(70 pages)ActiveForever Drive Medical Bed Assist Rail with Folding Bed Boa Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Gesundheit und Hygiene ActiveForever Drive Medical Bed Assist Rail with Folding Bed Boa.
Wir stellen 1 PDF-Handbücher ActiveForever Drive Medical Bed Assist Rail with Folding Bed Boa zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Commentaires sur ces manuels